Vivid I'm back again in Civic.....!!!! - Page 5

ante00 · 30th June 2008, 21:22

Well I bought them from ebay and her is link
eBay Motors: 07 HONDA CIVIC Door Sills Polished STEEL Sill Plate LED (item 300236211280 end time Jun-30-08 16:00:41 PDT)

amronno · 1st July 2008, 00:59

Ordered!
They are on their way across the 'pond' very soon!
Thanks again, ante!

NEEMSTAR · 1st July 2008, 01:04

i like them
do you know if they come in red
and how easy were they to install

ante00 · 1st July 2008, 01:33

They only come in light blue (something between light green and light blue), but it's very nice colour (you can see colour when LEDs are on my last 2 pics)....

Here is quick how to and I hope it would help.
First I removed inner door sills on front and back doors and lower central pillar area on both sides.
If you have orginal garnish (plastic one) they are held with clips like sills if you can take off clips off sills (cut on them first circle of clip....one which goes in panel/sill) or if you can't take them off buy few from honda and put them in holes where garnish goes.
Nest thing is to buy some strong double side tape (you'll need it). Double side tape you'll need it because one part of sills is little higher then on orginal sills. So now you cut little piece of tape on sill (part which goes near to inner of car; top part) and route the wire trough it, but first see where she will enter the car (I would advise a little part where door rubber isn't same beacuse there is little pit) so you want damage cable of sills. After you have routed cable on sill put tape you bought full lenght of sill in 2 layers.
Now you remove sticker for tape and put your sills in their place and watch out on wire. Next step is to connect little fusses/ballasts you got with sills and I would recommend you glove font and rear ballast together with some tape and install them in lower central pillar area near floor or on side (it's little tricky but you can manage it). When you have finally done all that use laces to routa cables like orginal ones and I forgot to say you need some extra wire so you can extend the ones from sill; since they aren't very long.

Where to install them? If you have footlights install them with them or if not I would recommend front internal lights (your choice). I have connected my sills to my floorlights.

And yes you don't need any special tool except your hands, some laces, double side tape, and knife (to cut parts of clip)
I don't know if this will help, but I can take some pics tomorrow and post them.

mike_civic · 1st July 2008, 07:47

ante00 these sills are very nice !

ante00 · 3rd July 2008, 00:22

here is few night shots of garnish and LED's....colour it isn't really blue; but it really fits quite nice with interior blue lightening

Vrachar · 3rd July 2008, 07:46

Great pics Ante!

ante00 · 8th September 2008, 16:31

well some little updates have came and some will come....

so far I installed Injen CAI on civic and I can only say WOOOW.....car feels different and it has great sound after 3000 rpms....and I also installed Eibach wheel spacers (10mm front and 20mm back) and car handeling is much better then beffore

I'll upload some pics as soon as I can and dyno chart after CAI installation (don't have any before CAI since I didn't got time to take car for dyno)

Wheelchair · 8th September 2008, 17:00

Those pics of the door garnish/LED's look very good.

They must look fantastic in the flesh!

ante00 · 1st October 2008, 17:46

Here are some pics of car I took over weekend....

here is tinted plexygkass with Oracal foil 8300

eibach spacers installed.....

and Injen CAI (nothing has been cut so filter can fit if you seen on last picture...)

Wheelchair · 1st October 2008, 17:47

Smart motor!!

Dimplyred · 1st October 2008, 17:50

Great looking car, well worth all the hard work.

Ivoke · 1st October 2008, 23:13

Quote:

Originally Posted by ante00

Here are some pics of car I took over weekend....

Good job man

Congratulation

Vrachar · 2nd October 2008, 15:48

WOW, just great Ante!

3rd July 2008, 00:22	#86 (permalink)
ante00 Supporter Magic Rear Seat Join Date: 18th April 2007 Location: Zagreb, Croatia Posts: 548 Thanks: 6 Thanked 10 Times in 10 Posts iTrader: (0)	here is few night shots of garnish and LED's....colour it isn't really blue; but it really fits quite nice with interior blue lightening Last edited by ante00; 3rd July 2008 at 01:17.

1st October 2008, 17:46	#90 (permalink)
ante00 Supporter Magic Rear Seat Join Date: 18th April 2007 Location: Zagreb, Croatia Posts: 548 Thanks: 6 Thanked 10 Times in 10 Posts iTrader: (0)	Here are some pics of car I took over weekend.... here is tinted plexygkass with Oracal foil 8300 eibach spacers installed..... and Injen CAI (nothing has been cut so filter can fit if you seen on last picture...) Last edited by ante00; 1st October 2008 at 17:52.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads for: I'm back again in Civic.....!!!!
Thread	Thread Starter	Forum	Replies	Last Post
Delivery time Civic been put back	Type S Bournemouth	Buying, Dealers and Servicing	12	2nd January 2007 17:27
Welcome back	elfa7	General Discussion	5	19th July 2006 21:32
We're back!	basegreen	Site suggestions, feedback and rules	10	17th July 2006 18:37


This thread is about: I'm back again in Civic.....!!!!, it's in Gallery at the Honda Civic forum Civinfo; Well I bought them from ebay and her is link eBay Motors: 07 HONDA CIVIC Door Sills Polished STEEL Sill Plate LED (item 300236211280 end ...

30th June 2008, 21:22	#81 (permalink)
ante00 Supporter Magic Rear Seat Join Date: 18th April 2007 Location: Zagreb, Croatia Posts: 548 Thanks: 6 Thanked 10 Times in 10 Posts iTrader: (0)	Well I bought them from ebay and her is link eBay Motors: 07 HONDA CIVIC Door Sills Polished STEEL Sill Plate LED (item 300236211280 end time Jun-30-08 16:00:41 PDT)

1st July 2008, 00:59	#82 (permalink)
amronno Just a basic member Magic Rear Seat Join Date: 8th August 2007 Location: Bergen, Norway Posts: 843 Thanks: 12 Thanked 11 Times in 11 Posts iTrader: (0)	Ordered! They are on their way across the 'pond' very soon! Thanks again, ante!

1st July 2008, 01:04	#83 (permalink)
NEEMSTAR Nobody gets out alive Rocketship door handle Join Date: 7th October 2007 Location: In your mind Posts: 1,393 Thanks: 30 Thanked 24 Times in 24 Posts iTrader: (0)	i like them do you know if they come in red and how easy were they to install

1st July 2008, 01:33	#84 (permalink)
ante00 Supporter Magic Rear Seat Join Date: 18th April 2007 Location: Zagreb, Croatia Posts: 548 Thanks: 6 Thanked 10 Times in 10 Posts iTrader: (0)	They only come in light blue (something between light green and light blue), but it's very nice colour (you can see colour when LEDs are on my last 2 pics).... Here is quick how to and I hope it would help. First I removed inner door sills on front and back doors and lower central pillar area on both sides. If you have orginal garnish (plastic one) they are held with clips like sills if you can take off clips off sills (cut on them first circle of clip....one which goes in panel/sill) or if you can't take them off buy few from honda and put them in holes where garnish goes. Nest thing is to buy some strong double side tape (you'll need it). Double side tape you'll need it because one part of sills is little higher then on orginal sills. So now you cut little piece of tape on sill (part which goes near to inner of car; top part) and route the wire trough it, but first see where she will enter the car (I would advise a little part where door rubber isn't same beacuse there is little pit) so you want damage cable of sills. After you have routed cable on sill put tape you bought full lenght of sill in 2 layers. Now you remove sticker for tape and put your sills in their place and watch out on wire. Next step is to connect little fusses/ballasts you got with sills and I would recommend you glove font and rear ballast together with some tape and install them in lower central pillar area near floor or on side (it's little tricky but you can manage it). When you have finally done all that use laces to routa cables like orginal ones and I forgot to say you need some extra wire so you can extend the ones from sill; since they aren't very long. Where to install them? If you have footlights install them with them or if not I would recommend front internal lights (your choice). I have connected my sills to my floorlights. And yes you don't need any special tool except your hands, some laces, double side tape, and knife (to cut parts of clip) I don't know if this will help, but I can take some pics tomorrow and post them.

1st July 2008, 07:47	#85 (permalink)
mike_civic Supporter Magic Rear Seat Join Date: 21st February 2008 Location: Piraeus, Greece Posts: 838 Thanks: 18 Thanked 21 Times in 21 Posts iTrader: (0)	ante00 these sills are very nice !

3rd July 2008, 07:46	#87 (permalink)
Vrachar Valve Cap Join Date: 12th June 2008 Location: Belgrade, Serbia Posts: 24 Thanks: 11 Thanked 2 Times in 2 Posts iTrader: (0)	Great pics Ante!

8th September 2008, 16:31	#88 (permalink)
ante00 Supporter Magic Rear Seat Join Date: 18th April 2007 Location: Zagreb, Croatia Posts: 548 Thanks: 6 Thanked 10 Times in 10 Posts iTrader: (0)	well some little updates have came and some will come.... so far I installed Injen CAI on civic and I can only say WOOOW.....car feels different and it has great sound after 3000 rpms....and I also installed Eibach wheel spacers (10mm front and 20mm back) and car handeling is much better then beffore I'll upload some pics as soon as I can and dyno chart after CAI installation (don't have any before CAI since I didn't got time to take car for dyno)

8th September 2008, 17:00	#89 (permalink)
Wheelchair Purveyor of Wit & Wisdom! Civinfo guru Join Date: 10th August 2007 Location: Chelmsford, Essex Posts: 3,480 Thanks: 33 Thanked 102 Times in 93 Posts iTrader: (0)	Those pics of the door garnish/LED's look very good. They must look fantastic in the flesh!

1st October 2008, 17:47	#91 (permalink)
Wheelchair Purveyor of Wit & Wisdom! Civinfo guru Join Date: 10th August 2007 Location: Chelmsford, Essex Posts: 3,480 Thanks: 33 Thanked 102 Times in 93 Posts iTrader: (0)	Smart motor!!

1st October 2008, 17:50	#92 (permalink)
Dimplyred Super Moderator Civinfo guru Join Date: 24th August 2007 Location: Staffordshire Posts: 4,737 Thanks: 19 Thanked 132 Times in 131 Posts iTrader: (0)	Great looking car, well worth all the hard work.

2nd October 2008, 15:48	#94 (permalink)
Vrachar Valve Cap Join Date: 12th June 2008 Location: Belgrade, Serbia Posts: 24 Thanks: 11 Thanked 2 Times in 2 Posts iTrader: (0)	WOW, just great Ante!