Speakers Will these 6.5" components fit a type S GT?

psykik · 17th November 2007, 15:22

Will these 6.5" components fit in a type S GT?

I've tried to get quotes from 3 installers, 2 have said theyd do it no problem, the 3rd a rarther experienced chap said NO, and if i did, id be wasting money cos they wouldnt sound right.

I checked out the Wiki but still couldnt be absolutely sure. I dont want to shoe horn the speakers in, cos theyre rarther expensive, so preferred a good fit and with adequate clearance after for a good SQ. Could some tell me definitively?

CS 265 Profi Vanadium - 2-way 17cm components
Mounting depth without / with ring:66 / 64mm (6.5" speaker )
37mm voice coil
CS 265 Vanadium
6.5 inch
Part number 231532
Peak power handling 180 Watt
Nominal power handling 120 Watt
Minimum amplifier power 75 Watt
Input sensitivity 90 dB 1W/1m
Frequency response 39 - 35.000 Hz
Impedance 4 Ohm
Crossover slope 2 x 18 dB/Oct.
Crossover frequency 2.400 Hz
Thermal protection HALO + PTC
Woofer W 165 Vanadium
Mounting depth without / with ring 66 / 64 mm
External diameter without / with ring 167 / 190 mm
External diameter with edges -
Installation diameter 145 mm
Fastening diameter 156 mm
Midrange -
Mounting depth without / with ring -
External diameter without / with ring -
External diameter with edges -
Installation diameter -
Fastening diameter -
Tweeter CAL 26 Titan VOF
Mounting depth 20 mm
External diameter 51 mm
Installation diameter 44 mm

Thanks

psykik · 17th November 2007, 15:23

PS i didnt want door builds done either.

psykik · 17th November 2007, 17:19

anyone?

Munro · 17th November 2007, 21:42

Have a look at the wiki . There are pictures of the speaker location with a tape measure to show all the various measurements.

The clearance to watch is the one with the window wound down - see picture 10.

Info - Pics of inside door panel with speakers - Civinfo Wiki

17th November 2007, 15:22	#1 (permalink)
psykik Supporter Triangular Exhaust Join Date: 28th April 2007 Posts: 447 Thanks: 0 Thanked 3 Times in 3 Posts	Will these 6.5" components fit a type S GT? Will these 6.5" components fit in a type S GT? I've tried to get quotes from 3 installers, 2 have said theyd do it no problem, the 3rd a rarther experienced chap said NO, and if i did, id be wasting money cos they wouldnt sound right. I checked out the Wiki but still couldnt be absolutely sure. I dont want to shoe horn the speakers in, cos theyre rarther expensive, so preferred a good fit and with adequate clearance after for a good SQ. Could some tell me definitively? CS 265 Profi Vanadium - 2-way 17cm components Mounting depth without / with ring:66 / 64mm (6.5" speaker ) 37mm voice coil CS 265 Vanadium 6.5 inch Part number 231532 Peak power handling 180 Watt Nominal power handling 120 Watt Minimum amplifier power 75 Watt Input sensitivity 90 dB 1W/1m Frequency response 39 - 35.000 Hz Impedance 4 Ohm Crossover slope 2 x 18 dB/Oct. Crossover frequency 2.400 Hz Thermal protection HALO + PTC Woofer W 165 Vanadium Mounting depth without / with ring 66 / 64 mm External diameter without / with ring 167 / 190 mm External diameter with edges - Installation diameter 145 mm Fastening diameter 156 mm Midrange - Mounting depth without / with ring - External diameter without / with ring - External diameter with edges - Installation diameter - Fastening diameter - Tweeter CAL 26 Titan VOF Mounting depth 20 mm External diameter 51 mm Installation diameter 44 mm Thanks

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads for: Will these 6.5" components fit a type S GT?
Thread	Thread Starter	Forum	Replies	Last Post
Wanted: Components, Bass, Amp - High end for SQ	psykik	For sale and Wanted	1	21st November 2007 00:54
Used type r "s" not selling on ebay	stewy123	Buying, Dealers and Servicing	10	26th September 2007 18:26
Which spec To type "S" or to type "R" that is the question	Clouseau	Buying, Dealers and Servicing	16	9th February 2007 14:48
components	apd	General Discussion	1	2nd November 2006 11:05
TYPE "S" 3 Door Civic	jayt43	General Discussion	10	29th June 2006 21:04


This thread is about: Will these 6.5" components fit a type S GT?, it's in Ipods, MP3 Players and ICE at the Honda Civic forum Civinfo; Will these 6.5" components fit in a type S GT? I've tried to get quotes from 3 installers, 2 have said theyd do it no ...

17th November 2007, 15:23	#2 (permalink)
psykik Supporter Triangular Exhaust Join Date: 28th April 2007 Posts: 447 Thanks: 0 Thanked 3 Times in 3 Posts	PS i didnt want door builds done either.

17th November 2007, 17:19	#3 (permalink)
psykik Supporter Triangular Exhaust Join Date: 28th April 2007 Posts: 447 Thanks: 0 Thanked 3 Times in 3 Posts	anyone?

17th November 2007, 21:42	#4 (permalink)
Munro Supporter Rocketship door handle Join Date: 10th August 2007 Location: Scotland Posts: 1,027 Thanks: 20 Thanked 16 Times in 12 Posts	Have a look at the wiki . There are pictures of the speaker location with a tape measure to show all the various measurements. The clearance to watch is the one with the window wound down - see picture 10. Info - Pics of inside door panel with speakers - Civinfo Wiki