2006+ Honda Civic Forum banner

Wifi obd

3418 Views 23 Replies 7 Participants Last post by  Scotty182
I have just bought a wifi obd scanner and using with iphone4. Iam having trouble connecting it to my civic cdti. I have used it on other cars with success. The car has been mapped and the map is locked. I have tried a few apps but just can't get it going on the civic I wanted to use my phone to try and log some data and see what boost am running.
1 - 20 of 24 Posts
Which app are you using ?
Have to sorted the connection settings properly ?
Can you read ECU codes using it ?

These scanners don't read/show the map itself, just sensor data the ECU reads, i wouldn't imagine it would make a difference being a locked map when using one of these
All new cars maybe OBDII but there is differnet versions of the protocol that the ECUs talk in.
Your OBDII reader might not be able to talk the same language ;)
On the iPhone, you need to set up a static ip address...

Go to wifi on your phone, select the wifi adaptor from the list of available wifi networks (mines CLK), then press the blue arrow, then in the next meny select 'Static' and enter:

IP Address: 192.168.0.11

Subnet mask: 255.255.255.0

Leave the other fields blank and then press 'WiFi Networks' on the top left to go back to the available networks, select your adaptor and exit setting :)

Should work now :)

What app are you using btw
See less See more
  • Like
Reactions: 1
On the iPhone, you need to set up a static ip address...

Go to wifi on your phone, select the wifi adaptor from the list of available wifi networks (mines CLK), then press the blue arrow, then in the next meny select 'Static' and enter:

IP Address: 192.168.0.11

Subnet mask: 255.255.255.0

Leave the other fields blank and then press 'WiFi Networks' on the top left to go back to the available networks, select your adaptor and exit setting :)

Should work now :)

What app are you using btw
Am using dash command and rev both won't work on the civic but fine with other cars
Is yours the Kiwi Replica ? says "wifi" on the front in green ?

Im using a similar adaptor and the Rev app without any issues
Is yours the Kiwi Replica ? says "wifi" on the front in green ?

Im using a similar adaptor and the Rev app without any issues
+1 That's the one I have too and the above works fine with both Rev and DC
Yeah that's the one green wifi on it
I now have it working I have change the ip 192.168.0.12 and all is good strange how it worked on other cars but not the civic
Thanks everybody for your input all is appreciated
Is anybody using this geting there apps from installous jail broke phone
Is anybody using this geting there apps from installous jail broke phone
Yes ;)

Did you try the static IP thing?
Yes ;)

Did you try the static IP thing?
Yeah change the last number on the ip from 11 to 12 and bingo it connects but still having bother reading live data with rev am going to restore my phone and jailbreak it again
Well that was of time. I have restored my phone and downloaded rev again still the same. It connects just wont read live data. I checked boost just sat at 18psi on tick over:) and it dont move. The speed just says 33mph and rpm 3333
Hi chaps where did you get your scanners from and what was the cost?
Try setting it as a kiwi in rev.
Get this coffee into me and am going back and having another go
Hi chaps where did you get your scanners from and what was the cost?
Good old eBay I got my from the uk 45 delivered next day was advertised at £70 or best offer. From seller Omar.m786. Make sure it's wifi and not Bluetooth.I made this silly mistake iPhones don't do Bluetooth well not properly. Think there more for android phones. I seen £10 and thought wow that's cheap so bought it However it will work with the laptop so have left it down the garage for the lads to use and I keep my wifi 1 handy.
  • Like
Reactions: 1
Try setting it as a kiwi in rev.
Just checked that's what it set to kiwi wifi. I can read fault codes. I had 1 stored from when I was doing the fuel filter. When I connect to rev the green box comes up in the top left with a tick and the voltage. But just won't let me read any data. Am go into the gauges click edit then swap then select air/fuel the boost has a green line under it click on boost then done. Am I going wrong any where
A lot of gauges are not supported by rev.. I prefer dash command and a lot of its gauges start working when you set up the vehicle profile ie curb weight, tyre size etc
Just checked that's what it set to kiwi wifi. I can read fault codes. I had 1 stored from when I was doing the fuel filter. When I connect to rev the green box comes up in the top left with a tick and the voltage. But just won't let me read any data. Am go into the gauges click edit then swap then select air/fuel the boost has a green line under it click on boost then done. Am I going wrong any where
is there an option to rescan available parameters ?
They normally have to interrogate the ECU to get valid ones before use.
I prefer Rev, but that's personal preference, both do the same job

Get everything plugged in and working the best you can, then unplug the wifi adaptor from the car and plug it back in, (rarely) mine takes two tries when its being fussy
1 - 20 of 24 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top