It's item 25 on this diagram, difficult to tell exactly where it sits though but it looks like the position near the rear drivers wheel(?)

CONTROL UNIT(CABIN)(RH)(1 ) for Honda CIVIC 2.0 TYPE-R PLUS 3 Doors 6 speed manual 2010 # HONDA CARS - Genuine Spare Parts Catalogue

www.parts-honda.uk

 

Thanks. I've ordered one from ebay for about £15. Let's see if it works. Not much to lose. There are lots on sale for about that much. Rather spend this than £700

Sent from my SM-G973F using Tapatalk

 

I changed the yaw rate sensor yesterday. It wasn't difficult to change. It is under the center console behind the handbrake. Still the abs/vsa lights are on. Disconnected the battery for about 10 minutes but made no difference. I've got a scan tool arriving today so I'll plug it in to see what next.

 

So I've scanned the codes. Even after clearing them, they keep coming back. I've attached some pictures if anyone can make sense of them.

 

My friend got the same code on his Accord with "loose" rear suspension (1 bolt was not tight) - yaw sensor was detecting movement.

 

I need to change my rear suspension anyway. I've got all the parts just waiting for the weather to clear up. I read that the brake pedal switch can cause these lights to come up as well. Other than that it drives fine, just the lights are there on dash. I wonder what this U0122 code is about

Sent from my SM-G973F using Tapatalk

 

U0122 Lost Communication With Vehicle Dynamics Control (VDC) Module

 

i think i might have got that on my old 8g after replacing front susspension and inner track rods
tracking was that far out it triggered some sensor

 

Started the car after work today and no warnings lights on. Drove it all the way home, still good. Plugged in the reader and cleared all the error codes and nothing reappeared. Hope it stays that way, fingers crossed.

 

So the abs/vsa/airbag/handbrake lights have come back on again tonight. I'm running out of ideas now. Might have to take it to an auto electrician to get to the bottom of this.

Sent from my SM-G973F using Tapatalk

 

did the same codes come back or different

 

Yes same codes as before. It's a bit strange that they disappeared for a few days

Sent from my SM-G973F using Tapatalk

 

I had abs/vsa/dws warnings recently on the Si and these came and went for a while before staying on.
Turned out to be the driver's rear ABS sensor.

 

I had the driver side rear sensor changed recently as it was showing up as failure but since the change no abs sensor code showing up, just these other ones.

Sent from my SM-G973F using Tapatalk

 

Update:

I took the car to an auto electrician. After a couple of hours of investigation, he said it’s abs pump failure. No point getting a new one as used ones are about £50-£60. Does anyone know how difficult it is to change if I was to try myself?


Sent from my iPhone using Tapatalk

 

Another update:

A couple of days ago. A thumping noise started coming from the front right when pressing the brake pedal for the first few minutes of each journey. I figured it would be the abs pump. Just to make sure, I took out the abs fuse and the noise stopped, put the fuse back and the noise started again.

I bought a used abs pump yesterday and got it fitted today. The thumping noise has gone and all the warning lights had gone but as soon as I drove off the abs light came on again. Scanned the car and it’s showing the code 14-1 front left wheel speed sensor failure. It comes back after clearing it.

I changed the front left sensor a couple of months ago with a sensor from eBay. I had to drill the old sensor out. The only thing I can think of now is either the ebay sensor is not good or I’ve damaged something while drilling.

Any suggestions anyone?


Sent from my iPhone using Tapatalk

 

Maybe you've damaged the sensor ring on the bearing when you drilled the sensor out?

 

That’s what I was thinking. Does the whole bearing need to be changed for that and how difficult of a job is that?


Sent from my iPhone using Tapatalk

 

This should be the Final Update on this

Got the front left Bearing and hub changed today and the abs/vsa lights have gone out, so it looks like I must’ve damaged the magnetic ring whilst drilling the old sensor out.

So the original problem I had was because of the abs pump but it was showing up as yaw rate sensor failure for some reason, there was nothing wrong with that.

The dashboard looks so different now after months of errors and check system lights showing


Sent from my iPhone using Tapatalk

 

Had this problem on my Civic. Tried everything to get rid of the vsa / abs lights and eventually i just had to fill the brake fluid reservoir a little bit more! Haven't lit up since. Easy step to try before replacing all the sensors. Hope this helps!